Free shipping to:

America: Canada, USA, Mexico

Africa: South Africa

Asia: Cambodia, China, HongKong, Indonesia, Japan, Macau, Malaysia, Philippines, Singapore, South Korea, Taiwan, Thailand, Vietnam

Europe: Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Netherland, Norway, Sweden, Switzerland, United Kingdom

Oceania: Australia, New Zealand

Russia (not available for far regions, the delivery delay may be 20-45 working days, depending on the destination, please contact us before making your purchase)

For more details, click here...

DTJ07401B-H, Wig-Wag Type 0-5V Throttle

Symmetrical throttle response in both forward and reverse directions

The Hall-effet throttle assemblies DTJ07401B-H are fully compatible with CURTIS ET-126 and ET-126 MCU, providing an analog 0-5V output proportional to throttle position for interfacing with CURTIS PMC motor speed controllers.

The throttle assemblies DTJ07401B-H are widely applied in EP and Noblift pallet stackers / trucks.

Specifications:

• Input voltage (volt): 24V-48V
• Signal output: 0-5V
• Maximum throttle output: 5.3V
• Minimum throttle output: 0V
• Maximum deadband at zero throttle: 10 degrees
• Maximum deadband at full throttle: 10 degrees
• Forward/Reverse current: 1.5A max
• Symmetrical throttle response in both directions

Key Features:

• Model: DTJ07401B-H (fully compatible with CURTIS ET-126 & ET-126 MCU)
• Hall effect sensors and ceramic power drivers minimize moving parts, thereby increasing reliability and Mean Time Between Failure.
• Symmetrical throttle response in both forward and reverse directions ensures smooth, concise acceleration and deceleration in both directions.
• Minimal deadband areas at both zero and full throttle positions eliminates hesitation when beginning to accelerate or decelerate.
• Environmental protection of major components through an epoxy layer over the circuit board assures operation in harsh environmental conditions.
• Wig-wag type throttle returns the throttle to neutral for convenience and safety.
• Input polarity protection to ensure no damage occurs to the throttle if it is incorrectly wired.
• Easy to install.

Optional operating handles (the handles are sold in pairs, one left and one right):
Optional connector (shell: TE 350782-1; socket: TE 350536-1):

We supply also:

• CURTIS ET-126 MCU
• CURTIS ET-165 MCU, with a 6-Pin Mate-N-Lock connector
• CURTIS ET-165E, with a 6-Pin Mate-N-Lock connector
• ET01316, compatible with CURTIS ET-191E

DTJ07401B-H, Wig-Wag Type 0-5V Throttle

Symmetrical throttle response in both forward and reverse directions

The Hall-effet throttle assemblies DTJ07401B-H are fully compatible with CURTIS ET-126 and ET-126 MCU, providing an analog 0-5V output proportional to throttle position for interfacing with CURTIS PMC motor speed controllers.

The throttle assemblies DTJ07401B-H are widely applied in EP and Noblift pallet stackers / trucks.

Specifications:

• Input voltage (volt): 24V-48V
• Signal output: 0-5V
• Maximum throttle output: 5.3V
• Minimum throttle output: 0V
• Maximum deadband at zero throttle: 10 degrees
• Maximum deadband at full throttle: 10 degrees
• Forward/Reverse current: 1.5A max
• Symmetrical throttle response in both directions

Key Features:

• Model: DTJ07401B-H (fully compatible with CURTIS ET-126 & ET-126 MCU)
• Hall effect sensors and ceramic power drivers minimize moving parts, thereby increasing reliability and Mean Time Between Failure.
• Symmetrical throttle response in both forward and reverse directions ensures smooth, concise acceleration and deceleration in both directions.
• Minimal deadband areas at both zero and full throttle positions eliminates hesitation when beginning to accelerate or decelerate.
• Environmental protection of major components through an epoxy layer over the circuit board assures operation in harsh environmental conditions.
• Wig-wag type throttle returns the throttle to neutral for convenience and safety.
• Input polarity protection to ensure no damage occurs to the throttle if it is incorrectly wired.
• Easy to install.

Optional operating handles (the handles are sold in pairs, one left and one right):
Optional connector (shell: TE 350782-1; socket: TE 350536-1):

We supply also:

• CURTIS ET-126 MCU
• CURTIS ET-165 MCU, with a 6-Pin Mate-N-Lock connector
• CURTIS ET-165E, with a 6-Pin Mate-N-Lock connector
• ET01316, compatible with CURTIS ET-191E